//This is the library to move a Servomotor with Attiny
class SoftwareServo {
  private:
    uint8_t pin;
    uint8_t angle;       // in degrees
    uint16_t pulse0;     // pulse width in TCNT0 counts
    uint8_t min16;       // minimum pulse, 16uS units  (default is 34)
    uint8_t max16;       // maximum pulse, 16uS units, 0-4ms range (default is 150)
    class SoftwareServo *next;
    static SoftwareServo* first;
  public:
    SoftwareServo();
    uint8_t attach(int);     // attach to a pin, sets pinMode, returns 0 on failure, won't
                             // position the servo until a subsequent write() happens
    void detach();
    void write(int);         // specify the angle in degrees, 0 to 180
    uint8_t read();
    uint8_t attached();
    void setMinimumPulse(uint16_t);  // pulse length for 0 degrees in microseconds, 540uS default
    void setMaximumPulse(uint16_t);  // pulse length for 180 degrees in microseconds, 2400uS default
    static void refresh();    // must be called at least every 50ms or so to keep servo alive
                              // you can call more often, it won't happen more than once every 20ms
};

SoftwareServo *SoftwareServo::first;

#define NO_ANGLE (0xff)

SoftwareServo::SoftwareServo() : pin(0),angle(NO_ANGLE),pulse0(0),min16(34),max16(150),next(0)
{}

void SoftwareServo::setMinimumPulse(uint16_t t) {
    min16 = t/16;
}

void SoftwareServo::setMaximumPulse(uint16_t t) {
    max16 = t/16;
}

uint8_t SoftwareServo::attach(int pinArg) {
    pin = pinArg;
    angle = NO_ANGLE;
    pulse0 = 0;
    next = first;
    first = this;
    digitalWrite(pin,0);
    pinMode(pin,OUTPUT);
    return 1;
}

void SoftwareServo::detach() {
    for ( SoftwareServo **p = &first; *p != 0; p = &((*p)->next) ) {
  if ( *p == this) {
      *p = this->next;
      this->next = 0;
      return;
    }
  }
}

void SoftwareServo::write(int angleArg) {
    if ( angleArg < 0) angleArg = 0;
    if ( angleArg > 180) angleArg = 180;
    angle = angleArg;
    // bleh, have to use longs to prevent overflow, could be tricky if always a 16MHz clock, but not true
    // That 64L on the end is the TCNT0 prescaler, it will need to change if the clock's prescaler changes,
    // but then there will likely be an overflow problem, so it will have to be handled by a human.
    pulse0 = (min16*16L*clockCyclesPerMicrosecond() + (max16-min16)*(16L*clockCyclesPerMicrosecond())*angle/180L)/64L;
}

uint8_t SoftwareServo::read() {
    return angle;
}

uint8_t SoftwareServo::attached() {
    for ( SoftwareServo *p = first; p != 0; p = p->next ) {
  if ( p == this) return 1;
    }
  return 0;
}

void SoftwareServo::refresh() {
    uint8_t count = 0, i = 0;
    uint16_t base = 0;
    SoftwareServo *p;
    static unsigned long lastRefresh = 0;
    unsigned long m = millis();

    // if we haven't wrapped millis, and 20ms have not passed, then don't do anything
    if ( m >= lastRefresh && m < lastRefresh + 20) return;
    lastRefresh = m;

    for ( p = first; p != 0; p = p->next ) if ( p->pulse0) count++;
    if ( count == 0) return;

    // gather all the SoftwareServos in an array
    SoftwareServo *s[count];
    for ( p = first; p != 0; p = p->next ) if ( p->pulse0) s[i++] = p;

    // bubblesort the SoftwareServos by pulse time, ascending order
    for(;;) {
  uint8_t moved = 0;
  for ( i = 1; i < count; i++) {
      if ( s[i]->pulse0 < s[i-1]->pulse0) {
    SoftwareServo *t = s[i];
    s[i] = s[i-1];
    s[i-1] = t;
    moved = 1;
    }
  }
  if ( !moved) break;
    }

    // turn on all the pins
    // Note the timing error here... when you have many SoftwareServos going, the
    // ones at the front will get a pulse that is a few microseconds too long.
    // Figure about 4uS/SoftwareServo after them. This could be compensated, but I feel
    // it is within the margin of error of software SoftwareServos that could catch
    // an extra interrupt handler at any time.
    for ( i = 0; i < count; i++) digitalWrite( s[i]->pin, 1);

    uint8_t start = TCNT0;
    uint8_t now = start;
    uint8_t last = now;

    // Now wait for each pin's time in turn..
    for ( i = 0; i < count; i++) {
  uint16_t go = start + s[i]->pulse0;

  // loop until we reach or pass 'go' time
  for (;;) {
      now = TCNT0;
      if ( now < last) base += 256;
      last = now;

      if ( base+now > go) {
    digitalWrite( s[i]->pin,0);
    break;
    }
  }
  }
}


// #include <SoftwareServo.h> -- We declared all the Servo library Code before
// Declare the variable to control the servo
SoftwareServo servoMotor;
int position = 0;

void setup() {
// Start the servo to work with pin 9
servoMotor.attach(0);
}

void loop() {
if (digitalRead(2) == HIGH) {
position = position + 5;
delay(100);
}

if (digitalRead(3) == HIGH) {
position = position - 5;
delay(100);
}

if (position > 180) {
position = 180;
}

if (position < 0) {
position = 0;
}

// Move to the 90º position
servoMotor.write(position);
SoftwareServo::refresh();
}
Week06P
